+86-574-87527771

[email protected]

Sitemap | RSS | XML

English

Home
About Us
Products
News
Download
Send Inquiry
Contact Us

> Message

Products

Metallic Gaskets
- Ring Joint Gaskets
- Kammprofile RTJ
Semi-Metallic Gaskets
Non-Metallic Gaskets

New Products

Neoprene Rubber O Rings
Silicon Rubber O Ring
EPDM Flange Rubber Gaskets
Double Jacket Gasket
Lens Ring Joint Gasket

All new products

Send Inquiry

For inquiries about our products or pricelist, please leave your email to us and we will be in touch within 24 hours.

Links：

Gasket machine
Spiral Wound Gasket
Expanded PTFE tape
Gasket machine
Flange insulation gasket kit
Vertical Slurry Pump

Contact Us

Address: No. 432, Zhenhai Middle Road, Luotuo Street, ZhenhaiDistrict, Ningbo City, Zhejiang China
Phone: +86-574-87527771
E-mail: [email protected]
Fax: +86-574-87527773
Skype:008618153328969

Inquiry For Price List

For inquiries about our products or pricelist, please leave your email to us and we will be in touch within 24 hours.

Latest News

FLANGE FACE TYPES2020/04/23
The flange face is the surface area that hosts the gasket. The 6 available types of flange face are flat (FF), raised (RF), ring joint (RTJ), lap joint, male and female (M&F), tongue and groove (T&G). Flanges with different faces require different gaskets and shall never be mated to prevent leakage of the joint. RF and FF flanges may have different types of “finish” (i.e. roughness on top the surface): smooth, stock and serrated.
Spiral wound gasket production process and equipment2017/10/31
In the present seal, metal spiral wound gasket with excellent elasticity, high temperature, high pressure,low temperature and other characteristics, has become a very wide range of applied seal. Especially suitable for uneven loading, relaxation and easy access together, cyclical changes in temperature and pressure of the occasion, is the main flange gasket. In the petrochemical pipelines, mechanicalseals,shipbuilding,metallurgy, aerospace and other industries widely.
Installing Grafoil Crinkle Gasket Tape2017/10/30
1. Brush off any rust or foreign particles. Wipe flange surface thoroughly with a rag soaked in acetone or other suitable solvent to remove grease or oil. 2. Insert fingernail between the paper backing strip and the tape and strip the paper back three to six inches. Draw a reference line in flange and press squared off end of tape against it. 3. Now, start laying the tape along the face of the flange, peeling the paper backing as you go. To prevent the adhesive surfaces of the tape from doubling back on themselves and sticking together, strip away only a few inches of paper at a time.
How to Cut Gasket material?2017/10/30
Clean radius and straight cuts are achievable on gasket material with the proper tooling. Thinner types of gasket material require nothing more than sharp blades and hollow gasket cutters. Gasket material over 1/4-inch thick require specialized mechanical tools to create the precision cuts necessary to seal a piece of equipment and is best left to professionals. Properly securing the gasket material and ensuring the tools used are in good condition will allow you to cut thinner gasket material efficiently and precisely.
Gasket Seating2017/10/30
There are two major factors to be considered with regard to gasket seating. The first is the gasket material itself. The ASME Unfired Pressure Vessel Code Section VIII, Division 1 defines minimum design seating stresses for variety of gasket materials.
Effecting a Seal2017/10/30
A seal is affected by compressing the gasket material and causing it to flow into the imperfections on the gasket seating surfaces so that intimate contact is made between the gasket and the gasket seating surfaces preventing the escape of the confined fluid. Basically there are four different methods that may be used either singly or in combination to achieve this unbroken barrier.

Copyright @ 2015-2022 Ningbo Kaxite Sealing Materials Co., Ltd. All Rights Reserved.

Links
Sitemap
RSS
XML
AMP
Privacy Policy

LiveChat关闭